Lane Brain
Publicado: Sab Sep 28, 2019 12:29 am
Escrito originalmente por Guest injectorman en 12 de Septiembre del 2010
Hi Guys,
Heres how the Lane Brain LED beacons are fitted and how multiple LEDs can be fitted to ensure successful lane changing even on the sharpest bends where the tail end of the car slides out.
Hola chicos,
Aquí es cómo el cerebro Lane LED faros están equipados y cómo múltiples LEDs pueden ser provistos para asegurar el éxito cambiando de carril
How it will be issued, with one LED.
On the rear. The 4 lower holes are for bridging wires necessary for multiple LEDs.
En la parte posterior. 4 agujeros inferiores son para salvar los cables necesarios para LEDs múltiples.
2 additional LEDs soldered to the board for use on bends.
2 LEDs adicionales soldados a la placa para su uso en las curvas.
On the back the 2 pins must be bridged to complete the circuit in series. (Only for multiple LEDS)
En la parte trasera de 2 pines debe ser un puente para completar el circuito en serie. (Sólo para múltiples LEDs)
Dimensions of the board
Trim off one end of the board and apply double sided tape to the space allocated at the other end of the board.
Here Ive taped over the 2nd and 3rd hole as they are not required. For multiple LEDs use the 8x10mm pad at either end for
the tape
Se quita un extremo de la tabla y aplique cinta adhesiva de doble cara para el espacio asignado en el otro extremo de la tabla.
Aquí he tapado el segundo y tercer agujero, ya que no son necesarios. Para LEDs múltiples utilice el teclado de 8x10mm en cada extremo para
la cinta
PLASTIC TRACK INSTALL
Here Ive used straight track as thats what I had lying around, obviously a multiple LED set up would be on or adjacent a bend.
Drill first hole 12mm offset from centre of rails. Drill 2nd and 3rd holes at further 8mm centres. Each hole is 7mm in diameter. Although Im currently using 8mm diameter and need to test more for the 7mm hole.
Aquí he utilizado la vía recta que eso es lo que había por ahí, obviamente, un múltiplo LED creado estaría en o cerca de una curva.
12mm Taladro primer hoyo desplazada desde el centro de los carriles. Taladro 2 y 3 agujeros en más de 8 mm centros. Cada hoyo es de 7 mm de diámetro. Aunque actualmente estoy usando 8 mm de diámetro y la necesidad de probar más por el agujero de 7 mm.
Neat and simple underneath. Double sided tape seems perfect for the job. The LED is now 2.5mm below track surface.
Atractivo y simple por debajo. la cinta de doble cara parece perfecto para el trabajo. El LED es ahora de 2,5 mm por debajo de la superficie de la pista.
Rick
Hi Guys,
Heres how the Lane Brain LED beacons are fitted and how multiple LEDs can be fitted to ensure successful lane changing even on the sharpest bends where the tail end of the car slides out.
Hola chicos,
Aquí es cómo el cerebro Lane LED faros están equipados y cómo múltiples LEDs pueden ser provistos para asegurar el éxito cambiando de carril
How it will be issued, with one LED.
On the rear. The 4 lower holes are for bridging wires necessary for multiple LEDs.
En la parte posterior. 4 agujeros inferiores son para salvar los cables necesarios para LEDs múltiples.
2 additional LEDs soldered to the board for use on bends.
2 LEDs adicionales soldados a la placa para su uso en las curvas.
On the back the 2 pins must be bridged to complete the circuit in series. (Only for multiple LEDS)
En la parte trasera de 2 pines debe ser un puente para completar el circuito en serie. (Sólo para múltiples LEDs)
Dimensions of the board
Trim off one end of the board and apply double sided tape to the space allocated at the other end of the board.
Here Ive taped over the 2nd and 3rd hole as they are not required. For multiple LEDs use the 8x10mm pad at either end for
the tape
Se quita un extremo de la tabla y aplique cinta adhesiva de doble cara para el espacio asignado en el otro extremo de la tabla.
Aquí he tapado el segundo y tercer agujero, ya que no son necesarios. Para LEDs múltiples utilice el teclado de 8x10mm en cada extremo para
la cinta
PLASTIC TRACK INSTALL
Here Ive used straight track as thats what I had lying around, obviously a multiple LED set up would be on or adjacent a bend.
Drill first hole 12mm offset from centre of rails. Drill 2nd and 3rd holes at further 8mm centres. Each hole is 7mm in diameter. Although Im currently using 8mm diameter and need to test more for the 7mm hole.
Aquí he utilizado la vía recta que eso es lo que había por ahí, obviamente, un múltiplo LED creado estaría en o cerca de una curva.
12mm Taladro primer hoyo desplazada desde el centro de los carriles. Taladro 2 y 3 agujeros en más de 8 mm centros. Cada hoyo es de 7 mm de diámetro. Aunque actualmente estoy usando 8 mm de diámetro y la necesidad de probar más por el agujero de 7 mm.
Neat and simple underneath. Double sided tape seems perfect for the job. The LED is now 2.5mm below track surface.
Atractivo y simple por debajo. la cinta de doble cara parece perfecto para el trabajo. El LED es ahora de 2,5 mm por debajo de la superficie de la pista.
Rick