Preguntas a RikoRocket

Responder
Avatar de Usuario
HAL
Site Admin
Mensajes: 175819
Registrado: Lun Sep 02, 2019 5:33 am

Preguntas a RikoRocket

Mensaje por HAL »

Escrito originalmente por M1K3LSLOT en 3 de Diciembre del 2007
Hola Riko, quiero hacer unas preguntas sobre algunas dudas del sistema, como usted sabe en mi casa corro sin los imanes suplementarios, asi pues para que aun cuando el coche derrapa si pasa por un lector de la pista no es leido mi solucion es esta de la foto.
Imagen
Imagen
En que puede afectar a la lectura de tiempos y posicion del coche? es importante que la pala de la guia corte antes que ser leido el led?
La otra consulta es sobre los mandos, el mando original lleva un potenciometro que da una lectura permanente, con un mando MB modificado da doce lecturas ¿resta eso efectividad a las 64 posciones del programa de la PB?
Riko Hello, I have some questions about some doubts system, as you know in my house without running additional magnets, so as to ensure that even if the car slipping if it passes by a reader of the track is not my read of this solution is photo.
Imagen
Imagen
In that could affect the reading time and location of the car? It is important that the blade guide the court before being led read?
The search is on the other commanders, command original wears a potentiometer which gives a continuous reading, with a command MB amended twelve gives readings Is it remains effective the 64 positions the agenda of the PB?



Avatar de Usuario
HAL
Site Admin
Mensajes: 175819
Registrado: Lun Sep 02, 2019 5:33 am

Mensaje por HAL »

Escrito originalmente por Guest midget99 en 3 de Diciembre del 2007
Riko, M1K3l runs without magnets. To make sure that laps are counted/car is identified, he uses the solution on the photo(s).
Question is: How may it affect readings (lap times and position)? Then he asks whether its important that the "guide blade (?)" is cut before the led is read?
Also, regarding the controllers, the original has a "potentiometer" giving a permanent reading, but a modified MB controller gives 12 readings. Will this diminish the effectiveness of the PB's 64 positions?

Avatar de Usuario
HAL
Site Admin
Mensajes: 175819
Registrado: Lun Sep 02, 2019 5:33 am

Mensaje por HAL »

Escrito originalmente por RikoRocket en 4 de Diciembre del 2007
midget99 escribió:Riko, M1K3l runs without magnets. To make sure that laps are counted/car is identified, he uses the solution on the photo(s).Question is: How may it affect readings (lap times and position)? Then he asks whether its important that the "guide blade (?)" is cut before the led is read?
Also, regarding the controllers, the original has a "potentiometer" giving a permanent reading, but a modified MB controller gives 12 readings. Will this diminish the effectiveness of the PB's 64 positions?
Nice solution! My friend AndyS on slotforum has integrated the LED into the guide blade just ahead of the blade, so similar.
This will not adversly effect the operation of lapcounting. In fact you must run from right to left over the powerbase, the first thing you pass is the LED reader, then at the white line you trigger the guide blade sensor. Yes it must read the LED before reaching the guide blade sensor, your solution is better than superslot. But be careful that the LED is central enough to be red by the sensor
You are completely correct, using a 12 step potentiometer will degrade the system performance. You will still get max speed and minimum speed, the control inbetween will not be so smooth or exact.
Cheers
Riko
Thanks midget99

Avatar de Usuario
HAL
Site Admin
Mensajes: 175819
Registrado: Lun Sep 02, 2019 5:33 am

Mensaje por HAL »

Escrito originalmente por Guest juanslot en 4 de Diciembre del 2007
RikoRocket escribió:Nice solution! My friend AndyS on slotforum has integrated the LED into the guide blade just ahead of the blade, so similar.This will not adversly effect the operation of lapcounting. In fact you must run from right to left over the powerbase, the first thing you pass is the LED reader, then at the white line you trigger the guide blade sensor. Yes it must read the LED before reaching the guide blade sensor, your solution is better than superslot. But be careful that the LED is central enough to be red by the sensor
You are completely correct, using a 12 step potentiometer will degrade the system performance. You will still get max speed and minimum speed, the control inbetween will not be so smooth or exact.
Cheers
Riko
Thanks midget99
¿Alguien me lo puede traducir (sin mucho esfuerzo) por favor? Esto me interesa bastante.

Avatar de Usuario
HAL
Site Admin
Mensajes: 175819
Registrado: Lun Sep 02, 2019 5:33 am

Mensaje por HAL »

Escrito originalmente por Guest allopez en 4 de Diciembre del 2007
RikoRocket escribió:Nice solution! My friend AndyS on slotforum has integrated the LED into the guide blade just ahead of the blade, so similar.This will not adversly effect the operation of lapcounting. In fact you must run from right to left over the powerbase, the first thing you pass is the LED reader, then at the white line you trigger the guide blade sensor. Yes it must read the LED before reaching the guide blade sensor, your solution is better than superslot. But be careful that the LED is central enough to be red by the sensor
You are completely correct, using a 12 step potentiometer will degrade the system performance. You will still get max speed and minimum speed, the control inbetween will not be so smooth or exact.
Cheers
Riko
Thanks midget99
Buena solución! Mi amigo AndyS de slotforum ha integrado el LED en la guía justo por delante, muy parecido.
Esto no afectará de manera adversa a la operación del conteo de vueltas. De hecho debes correr de derecha a izquierda de la centralita, lo primero que pasas es el lector del LED, entonces en la línea blanca disparas el sensor de la guía. Sí debe leer el LED antes de alcanzar el sensor de la guía, tú solución es mejor que la de superslot. Pero ten cudidado que el LED esté suficientemente centrado para ser leído por el sensor.
Tienes toda la razón, usando un potenciómetro de 12 posiciones degradará el rendimiento del sistema. Seguirás obteniendo el velocidad máxima y mínima, pero el control entre medias no será tan suave o exacto.
Imagen

Avatar de Usuario
HAL
Site Admin
Mensajes: 175819
Registrado: Lun Sep 02, 2019 5:33 am

Mensaje por HAL »

Escrito originalmente por Guest juanslot en 4 de Diciembre del 2007
Muchas gracias Allopez. Ha sido de gran ayuda.

Avatar de Usuario
HAL
Site Admin
Mensajes: 175819
Registrado: Lun Sep 02, 2019 5:33 am

Mensaje por HAL »

Escrito originalmente por M1K3LSLOT en 4 de Diciembre del 2007
Valla Juan tu idea del led en la guia tiene exito, haber como va la de las agujas de cambio, formamos el tandem-perfect.

Avatar de Usuario
HAL
Site Admin
Mensajes: 175819
Registrado: Lun Sep 02, 2019 5:33 am

Mensaje por HAL »

Escrito originalmente por M1K3LSLOT en 5 de Diciembre del 2007
Gracias por tu respuesta RiKo, lo del potenciometro ya me lo esperaba, ahora para los mandos de carcasa Parma tendre que buscar un potenciometro de 5 K lineal o magnetico y mecanizarlo en el mando, es que tengo las manos muy grandes para los mando de serie Imagen

Avatar de Usuario
HAL
Site Admin
Mensajes: 175819
Registrado: Lun Sep 02, 2019 5:33 am

Mensaje por HAL »

Escrito originalmente por Guest juanslot en 5 de Diciembre del 2007
M1K3LSLOT escribió:... como va la de las agujas de cambio...
Pues ya estás tardando.
M1K3LSLOT escribió:... formamos el tandem-perfect.
Si el maestro lo dice.

Responder

Volver a “Sistema SSD”